01.16.10
Posted in Blog, Amplifiers, Modern Tube, AES at by Simon
This Audio Electronic Supply AE-25 Superamp with oil caps is a great starter power amp. The tube complement includes :
- 2 NOS RCA cleartop 6CG7
- 2 NOS Amperex 7308
- New quad JJ/Tesla 6L6GC output tubes
For those not familiar with the Superamp, the beauty of this self-biasing amp is the wide range of output tubes which can be used in it: 6550, KT88, KT77, KT66, EL37, EL34, 6L6, and 6V6. Here are the manufacturer’s specs:
| Power output (RMS) |
15W RMS in triode mode into 8 ohms |
| Frequency response |
15Hz-20kHz +/- 0.5dB |
| Gain |
-91dB |
| Input impedance |
150K ohms |
| Sensitivity |
1.5V |
| Power requirements |
165W maximum, 80W stand-by |
This AE-25 was factory assembled by Cary Audio. The original MSRP for this amp with oil caps was $1500 assembled. You have to hear this amp to believe the musicality of its sound!
Here are the pictures:
Permalink
12.26.08
Posted in Blog, Amplifiers, Modern Tube, Cary at by Simon
The
Cary CAD 120S is rated at 60 watts per channel in triode mode and 120 watts per channel in ultralinear mode into an 8 ohm speaker load. Full rated output power is from 17 Hz to 23 kHz with less than 1% total harmonic distortion. The output stage may be switched ‘on the fly’ from triode mode to ultralinear mode by using a front panel selector button.
MSRP: $5500 (demo available)
Permalink
Posted in Blog, Preamplifiers, Modern Tube, Cary at by Simon
The Cary SLP 98P is a full feature, hand wired, vacuum tube preamplifier featuring (4) 6SN7, (2) 12AX7, and (2) 12AU7 tubes. MM phono amplifier section built in. Large heavy duty external power supply. Standard with remote volume. Jaguar Carnival Red chassis with clear coat finish. ZERO feedback design. SLP 98L has the same specification as above, but with line stage only.
MSRP: $4000 (line stage only, demo available), $4500 (with phono stage)
Permalink
Posted in Blog, Preamplifiers, Modern Tube, Cary at by Simon
The
Cary SLP 03 is a balanced vacuum tube preamplifier with dual 12AU7 vacuum tubes. It features full remote control for input switching and volume control. The front panel has a readout display for selected functions and current settings. The SLP 03 has 4 RCA stereo input pairs, one XLR input pair, a tape monitor loop and mute switching. Black or silver anodized aluminum faceplates. It has one set of XLR balanced outputs and dual RCA stereo outputs.
MSRP: $3000 (demo available)
Permalink
04.15.07
Posted in Blog, Amplifiers, Vintage Tube, Dynaco at by Simon
The Dynaco Stereo 70 is ‘’the'’ classic Dynaco stereo amplifier. The tube complement is four EL34s, two 7199s and a GZ34 rectifier tube. The early models are prized for their very high quality American-made output transformers with cloth leads. These are the only models that Tube Dreams restores. If you’re interested, you’ll find the specifications below.
Currently available ST-70s
I currently have one Audiophile restored ST-70 available for $849, includes new JJ/Tesla GZ34 rectifier, new matched quad SED (Winged C) EL34, NOS GE 7199 tubes. Alternatively, the amp is $799 with 6GH8A tubes and adapters.
Tube Dreams restorations
There are several possible levels of restoration that can be done to make the Stereo 70 sing, along with several optional improvements. These prices include the amp itself. If you have an amp you would like restored, please call to discuss. Typically a basic restoration costs about $200 plus tubes. The audiophile restoration costs another $100 or more depending on precisely what is done.
Basic restoration
The basic restoration replaces the bare minimum of parts to ensure that the power supply is stable and that the original sound quality is restored. The multi-section can capacitor (the silver cylinder) is replaced with a new American-made replacement, the selenium rectifier is replaced with a modern diode, the bias capacitors are replaced with new Sprague Atoms, and the 1W resistors in the power supply are replaced with modern 3W metal film resistors for a quieter power supply.
To restore the sound quality, the six coupling capacitors on the circuit board are replaced with new Solen Fast Capacitors, a superior high purity metallized polypropylene film capacitor.
Optionally, the two-conductor line cord is replaced with a modern three-conductor cord, and the four-screw speaker terminals are replaced with modern binding posts wired for your speaker’s impedance. Another optional modification is to use a higher capacitance multi-section can which increases the bass response.
The restored Stereo 70 is then retubed with new SED (formerly Svetlana) EL34 tubes, Sovtek or JAN Philips 7199 tubes, and a JJ (formerly Tesla) or vintage Mullard GZ34 rectifier. The amp is then biased, broken in, and then rebiased for optimal sound and tube life.
Audiophile restoration
The audiophile restoration builds on the basic restoration by also replacing the whole circuit board with a new board stuffed with modern components. The resistors are primarily Vishay/Dale metal film resistors, one of the most respected resistors in the audio industry. Some of the plate resistors are increased from 1 watt to 3 watts. Higher power capacity resistors will run cooler—and less heat means less noise. Metal film resistors are quieter than vintage carbon composite resistors, so the resulting sound is much cleaner with more detail.
Full restoration
For the full restoration, the chassis is completely stripped and rechromed. The original transformers are remounted and the amplifier is completely rebuilt using new tube sockets and all new components. This includes all the upgrades described in the basic restoration and audiophile restoration sections.
Audiophile boards and rebuild kits
We also sell replacement boards and rebuild kits if you’d like to do-it-yourself.
Specifications
*Power Output: 35 watts continuous, 80 watts peak each channel.
*Frequency Response: ±.5 dB from 10 cps to 40 kc.
*Power Response: 20 cps to 20 kc within 1 dB of 35 watts at less than 1% distortion.
*Intermodulation Distortion: Less than 1% at 35 watts (normally about .5%). Less than .05% at 1 watt.
*Hum and Noise: Inaudible; better than 90 dB below rated power.
*Sensitivity: 1.3 volts rms input for 35 watts out.
*Output Impedances: 4, 8, and 16 ohms each channel.
*Damping Factor: 15.
*Minimum Channel Separation: 55 dB
*Power Consumption: 190 watts 50/60 cps
*Preamp Provision: Two power takeoffs with independent heater windings to eliminate interaction. Each 6.3 volts 1 amp, 350 volts dc 10 ma. Dynakit preamplifiers plug in directly without modification.
*Tube Complement: EL-34 (4), 7199 (2), GZ-34.
*Size: 13″ by 9-1/2″ by 6-1/2″ high.
*Weight: 32 pounds.
*Finish: Chassis and bottom plate bright nickel plated. Cover finished in charcoal brown vinyl paint.
*Designed by: Ed Laurent, Bob Tucker
*Year Introduced: 1959
Permalink
